Κατάστημα
Bricks Set Nezha V1
Το σετ αυτό με τα δομικά στοιχεία, θα σας δώσει την δυνατότητα να αυξήσετε το πλήθος των δραστηριοτήτων από τις 32 Έτοιμες Δραστηριότητες που διαθέτει το NEZHA Inventor’s kit V2 for micro:bit σε επιπλέον 76 Έτοιμες Δραστηριότητες που διέθετε το προηγούμενο version 1 NEZHA Inventor’s kit for micro:bit .708232
micro:bit Wukong Expansion Board Adapter
Μικρό μέγεθος: 58mm*40mm, παρόμοιο σε μέγεθος με το BBC micro:bit (δεν περιλαμβάνεται).
Συμβατό με δομικά τύπου lego. Μπορεί να ενσωματωθεί εύκολα στις κατασκευές lego των παιδιών γιατί διαθέτει επαναφορτιζόμενη μπαταρία και μπορεί να συνδυαστεί με κινητήρες που επίσης είναι συμβατοί με δομικά τύπου lego.
Breakout Board πολλαπλής χρήσης: Η πλακέτα μπορεί να οδηγήσει 8x σερβοκινητήρες, 2x DC κινητήρες, διαθέτει 4x Rainbow LED, 8x απλά LED και βομβητή (buzzer).
Έχει ενσωματωμένη μπαταρία ιόντων λιθίου 400 mAh: Η φόρτιση διαρκεί 20 λεπτά και μπορεί να λειτουργήσει για περισσότερα από 40 λεπτά.
Τάση λειτουργίας: 3.7v~5v, οι περισσότερες θύρες I/O βγαίνουν σε 3 ακροδέκτες (Ground-Voltage-Signal) (GVS). Διατίθενται αυτόνομα IIC για OLED και BME280.Είναι πλήρες συμβατό με τους αισθητήρες Octopus.
Octopus:bit (Breakout Board For micro:bit)
Το Octopus:bit είναι ένα είδος πλακέτας breakout για micro:bit. Μπορεί να οδηγήσει σε θύρα GPIO, σειριακή θύρα, θύρα IIC και θύρα SPI στην πλακέτα micro:bit. Το μεγαλύτερο χαρακτηριστικό του Octopus:bit είναι ότι μπορεί να αλλάξει ηλεκτρικά επίπεδα για ορισμένες θύρες GPIO, γεγονός που καθιστά διαθέσιμο το micro:bit για προσαρμογή σε αισθητήρες 5V.
Nezha Breakout Board
NPP Μπαταρία μολύβδου 6V 1.2Αh
Number Construction Maths Activity Set
Geekservo 360 Degrees
Geekservo Continuous 360 Degrees
Geekservo DC Motor
RJ11 4P4C 200mm Καλώδιο (Πακέτο με 5)
micro:bit Breadboard Connector
Octopus 2 Channel Tracking Module
Octopus Sonar:bit
Octopus Analog Noise Sensor
Octopus Analog UV Sensor (GUVA-S12SD)
ELECFREAKS Octopus Analog UV Sensor (GUVA-S12SD) is the UV electric brick in our Octopus series, the basic design is from the Octopus electric bricks, and the setting of its outlook, the PCB fixing hole, and the connectors are the same.
It can measure the total UV intensity of the sunlight; linear signal voltage output; and it can be used as UV dosimeters, UV index instruments, and flame detection, etc,
Octopus 1 Channel Relay 3V
Octopus BME280 Pressure Sensor
Octopus CO2 Gas Sensor (MG811)
Octopus MG811 CO2 Gas Sensor is a CO2 electronic brick in our OCTOPUS series, the basic design for the outlook, PCB fixing holes and connections are the same as theirs.
The higher the CO2 concentration is, the lower the output voltage would be. The users can read the CO2 value easily after checking our brochures and coding samples.
The CO2 probe is made with an industrial grade that is highly allergic to CO2 and anti-interference to alcohol and CO. It is of high performance and quick response with a loaded signal amplification circuit even in different temperature and humidity environments. Besides, the heating circuit on-board helps to convert to stable 6V voltage from 5V directly improves the adaptability of the module.
Octopus Infrared Receiver Sensor
Octopus LM35 Analog Temperature Brick
This brick uses the LM35D LM35 Precision Centigrade Temperature Sensors from TI. The LM35 series are precision integrated-circuit temperature devices with an output voltage linearly- proportional to the Centigrade temperature. The LM35 device has an advantage over linear temperature sensors calibrated in Kelvin, as the user is not required to subtract a large constant voltage from the output to obtain convenient Centigrade scaling. The LM35 device does not require any external calibration or trimming to provide typical accuracies of ±1⁄4°C at room temperature and ±3⁄4°C over a full −55°C to 150°C temperature range. Lower cost is assured by trimming and calibration at the wafer level. The low-output impedance, linear output, and precise inherent calibration of the LM35 device make interfacing to readout or control circuitry especially easy. The device is used with single power supplies, or with plus and minus supplies. As the LM35 device draws only 60 μA from the supply, it has very low self-heating of less than 0.1°C in still air. The LM35 device is rated to operate over a −55°C to 150°C temperature range, while the LM35C device is rated for a −40°C to 110°C range (−10° with improved accuracy).
Octopus TMP36 Αισθητήρας θερμοκρασίας
Octopus PM2.5 Module
Octopus Single RGB Rainbow LED
Octopus Smoke Sensor MQ-2 Brick
The analog gas sensor - MQ2 is used in gas leakage detecting equipment in consumer and industry markets, this sensor is suitable for detecting LPG, i-butane, propane, methane, alcohol, Hydrogen, and smoke. It has high sensitivity and a fast response time. And the sensitivity can be adjusted by the potentiometer.